• On sale!
  • -10%
Thin Air Press Kit 36 x 52''

Thin Air Press Kit 36 x 52''

0 in Stock. Pre-order now and get 10% off. Estimated shipping date from the 28th of April.
€118.80 €132.00 -10%
Tax included
Time left

A simple and effective way to vacuum-laminate layers of veneer for large woodworking projects.

Valve position*
  • Center
  • Offset
Add a SuperPump
  • Yes
  • No
Add a sealing tape
  • Yes
  • No

Based on 4 reviews

Show reviews

Description

Thin Air Press Kit 36x 52" 

The Thin Air Press Kit 36x52'' is designed for laminating sheets of veneer together. 

It is ideal for larger projects like guitars, drums. Flat and curved furniture parts, such as curved-front drawer fronts, cabinet panels and table tops. Chess boards, and marquetry are frequently used in this size TAP Kit. 

Pressings can be flat, or used with an internal or external mold.

The kit can be re-used many times, and with a little care and maintenance, can last for hundreds of pressings.


How to use this product: 

  • insert your glued veneers (and mold) into the heavy-duty vinyl vacuum bag
  • position the breather netting under the valve
  • seal the bag
  • connect the manual pump
  • extract the air
  • leave your project to dry in the press


Position of the valve:
The valve can be positioned in the center (for most wood projects) or off-set for wet resin (epoxy) pressings. Please specify your choice when ordering.

If you choose an "offset" valve for working with epoxy, you can also use your press with woodworking glues. The offset valve is simply to ensure epoxy does not go up the valve and clog it.

Watch as it generates enough pressure to press veneers into the shape of your project.

Before you glue up your veneers, a dry run is highly recommended! We can't replace priceless sheets of veneer in case of a mishap. 

FAQ: 

Is this reusable, and for how many times?

The kits are designed to be used many many times. With a little care and maintenance, the TAP Kits will last for years.

Will the glue stick to the bag?

PVA glue and epoxy will not stick to the bag.
Any dried glue can be loosened with fingers and either shaken or blown out with a shop vac. Dry glue will not bond together.

How can I get the air out faster?

These larger bags have a lot of air in them at the start. A quick way to remove most of the air is to remove the top cap of the grey valve and hover a vacuum hose over the valve. Much of the air can be removed however vacuum cleaners are high volume but low pressure so they will not generate the pressure required to press a deck. Quickly reattach the cap onto the valve and finish the high pressure pumping using the Super Pump.

Why not use an electric pump system?

Because this is easier! The TAP valves are designed to work with the manual pumps supplied. The beauty of these one-way valves is that the pump does not need to be hooked up for the entire time the project is drying in the bag. The bag remains air tight, so that you dont need a constantly running pump. Once a project is pressed, it can be set aside while you go onto other pressings.

If the TAP Bag gets a hole in it, can I fix it?

Clear 2 packing tape seals up any suspected punctures. Use a length of the butyl tape to fix any side seam gaps or splits. See instructions for further details. 

Do the valves leak?

While many people assume air is leaking back through the valve, they are made of cast rubber and almost never leak. The most common problem with slow leakage is the open-end seal tape. If the seal is not properly closed up (check both sides) you will lose vacuum. If the top cap of the valve is not compromised with dust and debris, the valve will not leak.

Do you refund my veneer if the pressing doesn't work?

Sorry, we don't offer reimbursement in these cases.

Whats a Dry Run and why should I do that?

It means to press your project in the TAP bag, without putting any glue on the veneer sheets. Stack the dry sheets of veneer over the mold, seal them into the press with the breather netting in place, and pump the air out. Check for 10 minutes to make sure the TAP bag is not leaking. This will help you become familiar with the process before you commit glue to your veneer sheets.

Product Details

One way Valve
Choose centre or offset placed valve
Width
95.5 cm (36'')
Length
132 cm (52'')
Thickness
20 mil (0.5mm)
Tools included
Vacuum pump, extra sealing tape, breather netting and instructions
Strength of the Thin Air Press
Around* 14.22 psi (1kg/cm²)
TP36K

Reviews

No reviews

Customer reviews

Reviews about this product
0
1★
0
2★
0
3★
0
4★
4
5★
10/10


Based on 4 reviews

  • 5

    Great product , will be back to purchase again , Thanks ??

  • 5

    Solid product, but as is with anything new, practice first with some off cuts. One thing I want to try is put talcum powder inside the bag, because it sticks together too much. It's difficult to slide the board in. (Translated review)

  • 5

    Great quality product, very satisfied!

  • 5

    Compliant (Translated review)



Customers who bought this product also bought:

Product added to wishlist

By continuing to browse this site, you agree to the use of cookies to provide you with offers tailored to your interests, collect statistical data and allow the sharing of pages on social networks. More about it